||FYI||McCloskey Auto Service 2325 Montebello Square Dr Remodel Change of Occupancy
CN:Code: 09 IBC - 09 IFC - 11 PPRBC /Class: S1 / Const: VB /Stories: 1 /Size: 5580 /OL: 56
Date of plans: 04/9/14
You can access our web site for the latest fire department plan review comments:
1. From www.pprbd.org, select PLAN REVIEW then FIND PLANS next COLORADO SPRINGS
2. Scroll down to the correct address. You may then select APPROVED/DISAPPROVED to view comments associated with that particular project.
The storage, use and/or dispensing of hazardous materials within this facility shall be in accordance with all applicable provisions of the 2009 International Fire Code, as amended, including (but not limited to) Chapters: Hazardous Materials 27, and Flammable & Combustible Liquids 34.
|Attention||CHEMICAL INVENTORY, AS DECLARED
SEE ELECTRONIC DOCUMENTS
All interior storage in rooms 112 & 105:
New & used oil
windshield washer fluid
** These materials/hazard classes DO NOT exceed the maximum allowable quantities per control area as defined by 2009 IFC Table 2703.1.1(1) - (4) for flammable, combustible liquids in a non sprinklered area.
** These materials/hazard classes DO exceed the Hazardous Materials Permit Thresholds as defined in IFC Tables 105.6.20, 105.6.20, 105.6.8, 105.6.10
The General Requirements of 2009 IFC Sections 2701, 2703 and 3401 and shall apply for the use and storage of these materials.
THIS FACILITY IS REQUIRED TO HAVE AN HAZARDOUS MATERIALS OPERATIONAL PERMIT AND INSPECTION.
PLEASE APPLY FOR AN ANNUAL OPERATIONAL HAZARDOUS MATERIALS PERMIT AT THE CSFD WEBSITE: https://hammers.springsgov.com/submit
see attached information provided by CSFD
Storage and use of flammable and combustible liquids. The storage and use of flammable and combustible liquids in repair garages shall comply with Chapter 34 and Sections 2211.2.1 through 2211.2.4.
2211.2.1 Cleaning of parts. Cleaning of parts shall be conducted in listed and approved parts-cleaning machines in accordance with Chapter 34.
2211.2.2 Waste oil, motor oil and other Class IIIB liquids. Waste oil, motor oil and other Class IIIB liquids shall be stored in approved tanks or containers, which are allowed to be stored and dispensed from inside repair garages.
2184.108.40.206 Tank location. Tanks storing Class IIIB liquids in repair garages are allowed to be located at, below or above grade, provided that adequate drainage or containment is provided.
2220.127.116.11 Liquid classification. Crankcase drainings shall be classified as Class IIIB liquids unless otherwise determined by testing.
2211.2.3 Drainage and disposal of liquids and oil-soaked waste. Garage floor drains, where provided, shall drain to approved oil separators or traps discharging to a sewer in accordance with the International Plumbing Code. Contents of oil separators, traps and floor drainage systems shall be collected at sufficiently frequent intervals and removed from the premises to prevent oil from being carried into the sewers.
218.104.22.168 Disposal of liquids. Crankcase drainings and liquids shall not be dumped into sewers, streams or on the ground, but shall be stored in approved tanks or containers in accordance with Chapter 34 until removed from the premises.
222.214.171.124 Disposal of oily waste. Self-closing metal cans shall be used for oily waste.
2211.2.4 Spray finishing. Spray finishing with flammable or combustible liquids shall comply with Chapter 15.
2211.3 Sources of ignition. Sources of ignition shall not be located within 18 inches (457 mm) of the floor and shall comply with Chapters 3 and 26.
2211.3.1 Equipment. Appliances and equipment installed in a repair garage shall comply with the provisions of the International Building Code, the International Mechanical Code and NFPA 70.
2211.3.2 Smoking. Smoking shall not be allowed in repair garages except in approved locations.
|Attention||This facility DOES exceed the annual operational permit amount for a Hazardous Materials Permit.
APPLICATION FOR PERMIT IS FOUND AT IN THE CSFD HAMMERS ON LINE PERMIT PROGRAM @ https://hammers.springsgov.com/submit
The permit is automatically renewed annually and includes a permit inspection and associated permit fee.
If you have any questions please contact the Division of the Fire Marshal @ 719 385-5978.
|FYI||IFC 2009, AS AMENDED, CHAP 27
Quantities not exceeding the maximum allowable quantity per control area. The storage, use and handling of
hazardous materials in quantities not exceeding the maximum allowable quantity per control area indicated in Tables 2703.1.1(4) through 2703.1.1(4) shall be in accordance with Sections 2701 and 2703.|
** Refer to products MSDSs for storage, handling and use.
Open flames and high-temperature devices shall not be used in a manner which creates a Hazardous condition and shall be listed for use with the hazardous materials stored or used.
OWNER: Ensure that equipment does not create high temperatures and shall not create a hazardous condition. Chemical exposure to heat may cause adverse reactions with some of the chemicals listed.
|FYI||Above-ground tanks shall be provided with drainage control or diking in accordance with Chapter 34. Drainage control and diking is not required for listed secondary containment tanks. Secondary containment systems shall be monitored either visually or automatically. Enclosed secondary containment systems shall be provided with emergency venting in accordance with Section 2126.96.36.199.|
Incompatible materials in storage and storage of materials that are incompatible with materials in use shall be separated when the stored materials are in containers having a capacity of more than 5 pounds or 0.5 gallon. Separation shall be accomplished by:
1. Segregating incompatible materials in storage by a distance of not less than 20 feet.
2. Isolating incompatible materials in storage by a noncombustible partition extending not less than 18
inches above and to the sides of the stored material.
3. Storing liquid and solid materials in hazardous material storage cabinets.
4. Storing compressed gases in gas cabinets or exhausted enclosures in accordance with IFC 2009 Sections 2703.8.5 and 2703.8.6. Materials that are incompatible shall not be stored within the same cabinet or exhausted enclosure.|
|FYI||HAZARDOUS MATERIALS STORAGE CABINETS
Where storage cabinets are used to increase maximum allowable quantity per control area or to comply with chapter 27, such cabinets shall be in accordance with IFC 2009, as amended, Sections 2703.8.7.1 and 2703.8.7.2.
The interior of cabinets shall be treated, coated or constructed of materials that are nonreactive with the hazardous material stored. Such treatment, coating or construction shall include the entire interior of the cabinet. Cabinets shall either be listed in accordance with UL 1275 as suitable for the intended storage or constructed in accordance with the following:
1. Cabinets shall be of steel having a thickness of not less than 0.0478 inch (1.2 mm) (No. 18 gage). The cabinet, including the door, shall be double walled with a 11/2-inch (38 mm) airspace between the walls. Joints shall be riveted or welded and shall be tight fitting. Doors shall be well fitted, self-closing and equipped with a self-latching device.
2. The bottoms of cabinets utilized for the storage of liquids shall be liquid tight to a minimum height of 2 inches (51 mm).
Electrical equipment and devices within cabinets used for the storage of hazardous gases or liquids shall be in accordance with NFPA 70.
Cabinets shall be clearly identified in an approved manner with red letters on a contrasting background to read: HAZARDOUS-KEEP FIRE AWAY.|
|Attention||LIMIT CONTROLS AND VENTILATION
Indoor storage areas and storage buildings shall be provided with mechanical exhaust ventilation or natural ventilation where natural ventilation can be shown to be acceptable for the materials as stored.
Ventilation is required so that the level of vapors is maintained below the LFL or PEL. This will maintain a level of safety for the area.
*** Ventilation shall be in accordance with the International Mechanical Code and PPRBD Mechanical Dept.
|FYI||General precautions for the safe storage, handling or care of hazardous materials shall be in accordance with the IFC 2009, as amended, Sections 2703.9.1 through 2703.9.9.
- Personnel training and written procedures.
- Fire department liaison.
- Protection from vehicles.
- Electrical wiring and equipment. Electrical wiring and equipment shall be installed and maintained in
accordance with the ICC Electrical Code.
- Static accumulation.
- Protection from light.
- Shock padding.
|FYI||Labeling - An NFPA 704 compliant Hazard Placard is required for each pedestrian entry door rooms containing hazardous materials in excess of the exempt amounts (this door could be interior or exterior) and all such doors shall be included. The minimum size of the Hazard Placard shall be 15" by 15". This requirement is subject to verification at the time of the Hazardous materials Inspection prior to signing the Fire Final.
*** Refer to the product MSDS for NFPA 704 hazard ratings
Markings. Individual containers, cartons or packages shall be conspicuously marked or labeled in an
|FYI||Equipment, machinery, and required detection and alarm systems associated with the use, storage, or handling of hazardous materials shall be listed or approved. This requirement is subject to verification at the time of the Hazardous materials Inspection prior to signing the Fire Final.|
|FYI||CONTRACTOR: Prior to scheduling the Fire Final please contact the Hazardous Materials Inspector to arrange a Hazardous Materials Inspection prior to final signature being provided.
OWNER/CONTRACTOR: Contact the CSFD Office of the Fire Marshal at 719-385-5978 to schedule the hazardous materials construction inspection(s).|
Material Safety Data Sheets (MSDS) for all hazardous materials shall be either readily available on the premises as a paper copy, or where approved, shall be permitted to be readily retrievable by electronic access. Approved electronic access shall be as follows:
1. Media shall be USB Flash Drive.
2. Format shall be Microsoft Word 2000 or newer docu-ment, PDF, or other approved format.
Where a Knox Box is located at a facility, one USB de-vice shall be stored in the Knox Box and one device shall be located in an approved location(s). All devices and content shall be maintained.|