NOTE - THE NOTED DISAPPROVED ITEMS MAY NOT CONSTITUTE A COMPLETE LIST OF VIOLATIONS. THE DESIGNER IS TO CONDUCT A COMPLETE RE-REVIEW OF THE PLANS FOR ADDITIONAL VIOLATIONS OF THE STANDARD COMMENTS AND INCORRECT INFORMATION PRIOR TO RESUBMITTING.
System plans must be picked up within 30 days. All system plans left longer than 30 days will be discarded as abandoned.
KUM AND GO STORE NO 669
06735 CAREFREE CR N
||FYI||Kum and Go Store No 669, 6735 N Carefree Cir: new convenience store
SYSTEMS: fixed fire
CN:Code: 09 IBC - 09 IFC - 11 PPRBC /Class: M/ Const: V-B /Stories:1 /Size: 4958/OL: 94
FH:Required Flow: 2000 gpm /# Hydrants 2/On site flow:
DV: Proposing a 4958sf convenience store with fuel pumps.
Additional Comments:Located southeast of north Carefree Circle and Peterson Road.
* New K&G convenience store
* New canopy and dispensing pumps/islands 10 PUMPS
* Install THREE USTs and piping/vent system
* Hazmat review: 550/584 lb Carbon Dioxide vessel for beverage dispensing = 4,590 scf = 62 liq gallons;
**** THIS HM REVIEW AT THIS TIME DOES NOT INCLUDE THE UST INSTALLATION PERMIT
SUBMIT UST INSTALLATION PERMIT UNDER SEPARATE COVER TO 375 PRINTERS PKWY ATTN KAY YEAGER
You can access our web site for the latest fire department plan review comments:
1. From www.pprbd.org, select PLAN REVIEW then FIND PLANS next COLORADO SPRINGS
2. Scroll down to the correct address. You may then select APPROVED/DISAPPROVED to view comments associated with that particular project.
|Attention||CO2 DETECTION SYSTEM
CO2 detection-sensor-alarm system: note 16 ON PLAN SHEET M1 identifies owner provided CO2 SENSOR WITH INTEGRAL AUDIBLE ALARM 12-24" aff; ACI TYPE Q5 CO2-5000P-0-X. REV 06-04-12|
|Attention||IFC 2009, AS AMENDED
Automotive motor fuel-dispensing facilities, marine motor fuel-dispensing facilities, fleet vehicle motor fuel-dispensing facilities, aircraft motor-vehicle fuel-dispensing facilities and repair garages shall be in accordance with IFC 2009 as amended chapter 22 and the International Building Code, International Fuel Gas Code and International Mechanical Code.
Install tank per manufacturer's specifications and IFC 2009, AS AMENDED chapters 34 and 22.
Underground tanks for the storage of Class I, II and IIIA liquid fuels shall comply with Chapter 34, IFC 2009 ed.
|Attention||THE CHEMICAL INVENTORY, AS DECLARED, DOES EXCEED THE ALLOWABLE THRESHOLDS FOR THE ANNUAL HAZARDOUS MATERIALS OPERATIONAL PERMIT.
An annual Hazardous Materials operational permit is required:
* To store, handle or use Class I, Class II or Class III-A liquids in excess of 25 gallons in a building or in excess of 60 gallons outside a building.
* To engage in the dispensing of liquid fuels into the fuel tanks of motor vehicles at commercial, industrial, governmental or manufacturing establishments.
* 550 LB CO2 (inert/asphyxiant = 4,590.scf ********** (BELOW permit threshold = 6,000 cf)
* Refrigerants = 16 lbs total refrigerant; maximum per circuit 6.69 *****(BELOW permit threshold = 220 lbs per circuit)
*** This facility is required to apply for the Annual Hazardous Materials Operational Permit at the CSFD website:
*** To Schedule the hazardous materials construction inspection and annual operational permit inspection please contact the Division of the Fire Marshal @ 719-385-5978.
*** For further questions or information please contact the Division of the Fire Marshal main number at 719-385-5978 or Kay Yeager @ 719-385-7356. |
|Attention||LIQUIFIED PETROLEUM GAS (LPG)
*** Facility declares one LPG cabinet for LPG cylinder exchange
Amount: 73 gal w.c.
CSFD ADMINISTRATIVE RULING 2011-002
Required operational permits 105.6.27, Required Construction Permits 105.7.10, and Permits 3801.2 of the IFC 2009, as amended. Permits shall be required as set forth in Sections 105.6.27 and 105.7.10.
A permit is required to install one or more LP-gas cabinets associated with a cylinder exchange program. This shall include all occupancies where LP-gas is stored, used or handled as part of a cylinder exchange program. Containers that are filled, partially filled or empty shall be considered as full containers.|
|Attention||It is the responsibility of the Tank Installation Contractor to apply for and obtain a Tank Installation Permit from the CSFD Office of the Fire Marshal, 375 Printers Parkway.
The Tank Installation Contractor is required to submit for, and receive a separate permit for the installation of any new vessel in excess of 60 gallons that contains hazardous materials. This permit must be obtained prior to installation. The tank may not be filled until after inspection. Applications for tank permits can be obtained from the CSFD Office of the Fire Marshal, 375 Printers Parkway.
Submittals for new tank permits shall include, but not limited to FULL SIZE SET OF PLANS AND ONE QUARTER SIZE SET OF STAMPED PLANS. Dimensioned site plan that shows the location of the tank, a declaration of size/contents, manufacturer's cut sheets that show the construction/material that the tank is made of and the method/available volume of secondary containment in accord with Chapter 27 of the 2009 International Fire Code. vehicular protection devices, if required, shall also be shown and described on the site plan. Plans shall show all piping systems, valves, components, equipment and vent systems.
2/15/12 phone call
**** Per Tiffany Hammerly, Kum & Go preconstruction associate, SENACA company will be responsible for applying for the UST installation permit and providing full size set of complete tank, piping, vents, and dispensing pump plans for review to the CSFD. UST TANK PERMIT & PLANS SHALL BE COMPLETED UNDER SEPARATE REVIEW--SEPARATE COVER & DEFERRED SUBMITTAL.
THREE USTS: ONE 20K, TWO SPLIT 12K/8K
|FYI||*** REMINDER*** FYI
The State of Colorado permits the installation of USTs/ASTs ---
When submitting the UST installation permit and plans to the COLORADO SPRINGS FIRE DEPT, for the 3 USTs, please provide copies of all permit and plan documents submitted to the Colorado Div. of Labor & Employment, Oil & Public Safety|
Approved, clearly identified, and readily accessible emergency disconnect switches shall be provided at approved locations to stop the transfer of fuel to the fuel dispensers in the event of a fuel spill or other emergency. Two emergency disconnect switches for exterior fuel dispensers shall be required as follows:
1. Exterior: Shall be located within 100 feet of, but not less than 20 feet from, the fuel dispensers. Provide a mushroom style switch that is readily accessible and must cut off power to all dispensers and pumps.
2. Interior: Shall be located at the Attendant duty location. Provide a palm-type switch button which will shut off the flow of fuel and cut off power to all dispensers and pumps.
3. Emergency disconnect switches shall shut-off the power in conformance with the National Electric Code (National Fire Protection Association (NFPA-70)) and NFPA-30A.
4. Emergency controls shall be of a type which is only manually resettable.
For interior fuel-dispensing operations, the emergency disconnect switch shall be installed at an approved location.
Signs shall be provided in approved locations and of the legible size:
1. Interior: At least 1 inch in height and 1/8 inch stroke Red on White background
2. Exterior: At least 2 inches in height and ¼ inch stroke Red on White background.
|FYI||ONE, 550 lb CARBON DIOXIDE VESSEL (CO2)
4,590 CUBIC FEET
CarboMizer 550 bulk;
NFPA = 3-0-0 special = SA (liquified)
NFPA = 1-0-0 special = SA (gas)
TLV-TWAs, 5000 ppm (ACGIH, 2004)
TLV-TWA 15 MIN STEL 30,000 ppm
High Pressure liquid and gas. Can cause rapid suffocation....CO2 IS AN ASPHYXIANT
May cause frostbite.
****** ATTENTION *******
Indoor storage of compressed gases falling into categories such as asphyxiants, irritants can be hazardous regardless of the type of gas involved simply due to the hazards related to asphyxiation.
VENTILATION SHALL BE MAINTAINED AND OPERATIONAL. See ventilation comments.
The carbon dioxide shall be transferred---loaded and off loaded through a fill connection located directly adjacent to the tank at the exterior of building.
ATTENTION: Duplicate gauges shall be installed at the filling connection to enable the driver to fill the container and maintain the required pressure in the container.
Pressure relief devices and vents shall be piped to discharge outside in a safe direction.
NOTE: Storage areas where an accumulation of inert gas could occur should be continuously monitored with an appropriate alarm system to indicate an oxygen deficient atmosphere. see plan sheet M1 SHOWS INSTALLATION OF CO2 SENSOR. OK
|I||Equipment schedule identifies one carbon dioxide container; equipment plan sheet shows one CO2 container,
*** Compressed gas containers, cylinders, tanks and systems shall not be placed in areas where they are capable of being damaged by falling objects.
****Please maintain a minimum of 1 foot clearance between rack storage and tank. Do not store materials above CO2 tank. |
|FYI||CO2 VESSEL AND PIPING SYSTEM
**** Containers, cylinders and tanks shall be designed and constructed in accordance with approved standards. Containers, cylinders, tanks and other means used for containment of hazardous materials shall be of an approved type. Pressure vessels shall comply with the ASME Boiler and Pressure Vessel Code.
note: Container spec sheet; CHART; declares ASME Compliant
*** Piping, tubing, valves and fittings conveying hazardous materials shall be designed and installed in accordance with approved standards and shall be in accordance with IFC 2009 Sections 2703.2.2.1 and 2703.2.2.2.
***ATTENTION: Piping, tubing, hoses anf fittings shall be designed to a bursting pressure of at least four times the system design pressure.
Materials of construction shall be employed for a potential exposure to a temperature of -109.3 degrees F.|
Facilities shall declare the storage and use of small Insulated Carbon Dioxide Systems used in Beverage Dispensing.
Gaseous Carbon Dioxide is an asphyxiant gas and exposure to high concentrations may cause toxic effects including asphyxiation. To provide for the safety of building occupants and emergency personnel, ventilation in accordance with the IFC Sections 3007.2, 2704.3 or 2705.1.9 is required where concentrations of this gas are stored or present.
ATTENTION*** THIS CO2 SYSTEM INCLUDES A CONTAINER >100 LBS, THEREFORE REQUIRES VENTILATION IN ACCORDANCE WITH THE IMC/IFC 2009. VENTILATION REQS. ARE SETFORTH IN IFC 2009, 3007.2; 2704.3 OR 2705.1.9 AND IMC 2009, SECTION 502.8.1, 502.8.1.1
All new or proposed building ventilation system designs shall submit for review to the Pikes Peak Regional Building Department.
*** ATTENTION**** 2704.3 VENTILATION
Indoor storage areas and storage buildings shall be provided with mechanical exhaust ventilation or natural
ventilation where natural ventilation can be shown to be acceptable for the materials as stored.
System requirements. Exhaust ventilation systems shall comply with all of the following:
1. Installation shall be in accordance with the International Mechanical Code.
2. Mechanical ventilation shall be at a rate of not less than 1 cubic foot per minute per square foot of floor area over the storage area.
3. Systems shall operate continuously unless alternative designs are approved.
4. A manual shutoff control shall be provided outside of the room in a position adjacent to the access door to the room or in an approved location. The switch shall be of the break-glass type and shall be labeled:
VENTILATION SYSTEM EMERGENCY SHUTOFF.
5. Exhaust ventilation shall be designed to consider the density of the potential fumes or vapors released. For
fumes or vapors that are heavier than air, exhaust shall be taken from a point within 12 inches of the floor.
|FYI||VENTILATION 2704.3 CONTINUED
6. The location of both the exhaust and inlet air openings shall be designed to provide air movement across all
portions of the floor or room to prevent the accumulation of vapors.
7. Exhaust ventilation shall not be recirculated within the room or building if the materials stored are capable of
emitting hazardous vapors.
*** PPRBD Mechanical Dept. has NOT review/released for permit these plans. Disapproval may not be associated with CO2 system.
A CO2 sensor has been chosen option in lieau of ventilation, per revised CSFD Admin ruling. OK|
2-A:20-B:C located not more than 75 feet from pumps, dispensers or storage tank fill-pipe openings.
Warning signs in the fuel-dispensing area:
1. It is illegal and dangerous to fill unapproved containers with fuel.
2. Smoking is prohibited.
3. The engine shall be shut off during the refueling process.
4. Portable containers shall not be filled while located inside the trunk, passenger compartment, or truck bed of a vehicle.
|FYI||Labeling - An NFPA 704 compliant Hazard Placard is required for each pedestrian entry door rooms containing hazardous materials in excess of the exempt amounts (this door could be interior or exterior) and all such doors shall be included. The minimum size of the Hazard Placard shall be 15" by 15". This requirement is subject to verification at the time of the Hazardous materials Inspection prior to signing the Fire Final.|
|Attention||NOTE TO CONTRACTOR & FIRE INSPECTOR: Prior to scheduling the Fire Final please contact the Hazardous Materials Inspector to arrange a Hazardous Materials Inspection prior to final signature being provided.|
|FYI||Equipment, machinery, and required detection and alarm systems associated with the use, storage, or handling of hazardous materials shall be listed or approved. This requirement is subject to verification at the time of the Hazardous materials Inspection prior to signing the Fire Final.|
Possess a minimum, Colorado Oil and Public Safety (OPS) Class C Operator certification. Records shall be kept at the premises or made available for inspection by the fire code official within 24 hours of a written or verbal request.|
|FYI||A minimum of 1 set of Material Safety Data Sheets (MSDS), hard copy, must be readily availiable on the premises at all times.|